Draper SL10 Provozní pokyny stáhnout pdf

Caution:

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions completely before proceeding.

DANGER: To reduce risk of shock:

 Always disconnect power from lift before cleaning.

WARNING–To reduce risk of burns, ﬁres, electric shock or injuries to persons:

 Disconnect power from lift before putting on or taking off parts.

 Use this lift only for its intended use as described in these instructions. Do

not use attachments not recommended by the manufacturer.

 Never operate this lift if it has a damaged cord or plug. If it is not working

properly, call your dealer or the manufacturer for assistance/repair.

 Keep cords away from heated surfaces.

 Never operate lift with air opening blocked. Keep the air openings free of lint,

hair, and the like.

 Never drop or insert any object into any opening.

 Do not use outdoors.

 Route cords and cables as shown in the instructions.

 WARNING: Risk of Electric Shock—connect this product to a

properly grounded electrical supply.

IMPORTANT INSTALLATION/OPERATING INSTRUCTIONS

WARNING: To prevent injury, this apparatus must be securely attached to the

building structure in accordance with the instructions.

Caution: Do not operate Scissor Lift SL without a minimum of 15 lbs. of weight

attached to the pan. Operating without weight may cause cables to unspool.

 Test lift prior to installation. Please Note: Packaging must be removed from

lift before testing.

 Follow instructions carefully. Installation contrary to instructions invalidates

warranty.

 Do not obstruct operation of Scissor Lift SL with ﬁngers or any object.

Serious injury or damage could result.

 Lift is intended for use with product weighing not more than 100 pounds.

 Scissor Lift SL is designed to accommodate ceiling suspended equipment.

Equipment should not be allowed to rest on optional ceiling closure

during operation (refer to section titled “Installing Projector”).

 Entire bottom of unit must be unobstructed to permit proper operation.

Sufﬁcient clearance must be allowed below projector or optional ceiling

closure: 4' for Model SL4, 10' for Model SL10, etc.

 Unit must be installed level (use a carpenter’s level).

 Unit operates on 115V AC 60 Hz. current. 9.06 amps current draw (2.06

amps for lift, 7 amps for outlet).

 Verify the show position when testing lift. Make required changes by referring

to adjustment instructions on page 4 of this document.

 The maintenance/service factory limit setting must not be adjusted to a lower

position than the preset factory limit setting. In addition, Draper does not

recommend setting show position at the maintenance/service position—for

example, if you wish to have 8' show position, order a lift with at least a 10'

maintenance position.

 When the Scissor Lift SL is to be installed in “other space used for

environmental air” the optional environmental air space housing must

be installed per instructions to isolate the lift from the “other space

used for environmental air.”

 When Scissor Lift SL is NOT installed in environmental air space housing

and optional ceiling closure, the ALTERNATE wiring for up limit switch may

be used (see Alternate Wiring schematic on page 5).

CAUTION: Before servicing unit, disconnect hardwired control and

any remote control.

Note: Unit has been thoroughly inspected and tested at factory and found

to be operating properly prior to shipment.

Planning

 Based on screen location and projector speciﬁcations, determine proper

position for projector installation.

 Conﬁrm that there is adequate space for installation and operation. Minimum

clearance above ceiling level varies according to Scissor Lift model, plus height

of projector, optional mounting bracket, optional ceiling closure, and optional

Environmental Air Space Housing.

 Arrange to provide service access to the unit.

 Maximum lifting capacity is 100 lbs.

As Soon As Scissor Lift Arrives

 Open carton and inspect for damage.

 Locate the following parts:

A. The unit itself

B. Controls

C. Optional equipment: Environmental Air Space

Housing, Universal Projector Mount, closure panel or ceiling ﬁnish kit

(all ship in separate cartons).

 Test lift prior to installation. Please Note: Packaging must be removed from

lift before testing.

Important Safety/Installation/Operating Instructions

Scissor Lift SL Video Projector Lift by Draper

Save These Instructions

Electrical Connections

Unit operates on 115V AC, 60 Hz. current. 9.06 amps current draw (2.06 amps

for lift, 7 amps for outlet). Opening the electrical box exposes terminals for ﬁeld

connections. Unit is shipped with internal wiring complete.Wire to connect unit to

power supply should be furnished by installer. Connections should be made in

accordance with wiring diagram, and wiring should comply with national and local

electrical codes. An appropriate disconnect device shall be provided as part of the

building installation. All operating switches

should be “off” before power is connected.

If you encounter any difﬁculties installing or servicing your Scissor Lift SL, call your

dealer or Draper, Inc. in Spiceland, Indiana, 765-987-7999, or fax 765-987-7142.

Operation

Before operating or testing the unit, make sure the

packaging has been removed from the unit. Remove the

corrugated block from the cardboard sleeve (bottom-most

packaging material), then collapse the sleeve and remove it,

along with the rest of the packaging. Next, operate the lift in

the "up" direction, so the lift's control encoder will recognize

it's "home" location. Until you do this, the Down function will

not work. You must also do this if the Scissor Lift ever

loses or is disconnected from the power.

When unit is ﬁrst operated, be cautious! If unit fails

to operate properly, press “off” and recheck electrical

connections before proceeding. Cycle unit down and up

several times to conﬁrm satisfactory operation.

Caution: Do not pull on or touch safety belt when unit

is in motion. If belt locks, the cables will unspool.

Caution: Obstructing bottom pan may cause cables

to unspool.

Caution: Do not operate Scissor Lift SL without a

minimum of 15 lbs. of weight attached to the pan.

Operating without weight may cause cables to unspool.

Standard Single Station Low Voltage Control (See Fig. 1)—One three-button

switch with “up”, “down”, and “off” buttons. Lift starts up or down when appropriate

button is pressed, and may be stopped by pressing “off” button. Factory set

limit switches stop lift automatically when projector is in “show” position. One

momentary key switch lowers lift from “show” to “service” position.

Optional Multiple Station Control—Optional, moves lift from “stored” to “show”

position only. Each switching station has a three-button switch with “up”, “down”,

and “off” buttons. Lift starts up or down when appropriate button is pressed,

and may be stopped by pressing “off” button. Factory set limit switches stop lift

automatically when projector is in “show” position.

Optional Key Operated Switch—If ordered, the standard LVC-S can be replaced

with a second single station, momentary key-operated three position (up/off/down)

switch. Multiple Station Control required for this option. Moves lift from “stored” to

“show” position only.

Optional Infrared or Radio Frequency Remote Control—If ordered, a three-

button transmitter is provided, with “up”, “down”, and “stop” buttons. Unit starts up

or down when appropriate button is pressed, and may be stopped by pressing

“off” button. Factory set limit switches stop unit automatically when projector is in

“show” position. Only controls "show" and "stored" positions.

Optional RS232 Control—For Serial communication an R2D7 Serial

Communications Interface is optionally available.

Low Voltage Trigger—Input provided for Low Voltage Trigger from projector (see

diagram on page 4).

Please Note: Scissor Lift SL must be installed in accordance with the requirements

of the Local Building Codes, the Canadian Electrical Code (CEC), CAN/CSA

C22.1 and the National Electric Code (NEC), NFPA 70, as required. An appropriate

disconnect device shall be provided as part of the building installation.

D C U

2¾"

4½"

/8"

Front Side Back

LVC-S

Up & Show

OFF

DOWN

OFF

SP-KSM

Service

Figure 1

Caution:

Beware

of pinch

points

U.S. Patent

Number

D395,909

WARNING/AVERTISSEMENT

RISK OF ELECTRIC SHOCK. DO NOT OPEN

RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR.

Caution: Make sure electrical supply has been disconnected before

attempting to connect Scissor Lift to electricity.

Scissor Lift should be operated and checked prior to installing projector and/or

optional ceiling closure. Low Voltage Control Switch shown below comes with 75'

of non-plenum rated cable and should be plugged in to Control Panel on top frame

of lift for control of the "Up" and "Show" positions. Momentary Key Switch shown

below comes with 75' of cable and should be plugged in to Control Panel on top

frame of lift for control of the "Service" position.

Scissor Lift SL is approved to UL 2442 and CSA C22.2 No. 60065-03.

1 2 3 4 5

Shrnutí obsahu

Strany 1 - Save These Instructions

Strany 2 - page 2 of 5

Scissor Lift SL by Draper page 2 of 5Installing Projector Generally, the video projector should be suspended from the Projector Pan according to pro

Strany 3 - page 3 of 5

Scissor Lift SL by Draper page 3 of 5Installing Optional Ceiling Closure If your Scissor Lift SL is equipped with optional ceiling closure, it can b

Strany 4 - Low voltage

KEYWALLRP/RQRP/RQLVTRP/RQ Bus Ports forremote controls such asIR Eye, RF Receiver, LEDWall Switch and RS232Low Voltage Tr igger(6-24 VDC)(No +/- wiri

Strany 5 - *Black (BK) Jumper wire is

Scissor Lift SL by Draper page 5 of 5www.draperinc.com (765) 987-7999Wiring SchematicNU C DDashed wiring by electrician115V ac,SupplyAttached to lowe

Další dokumenty pro Připojení projektoru Draper SL10

Zobrazit dokument Draper SL10 Uživatelský manuál

Draper SL10 Uživatelský manuál (4 stránky)

Komentáře k této Příručce

Žádné komentáře

Draper SL10 Provozní pokyny

Procházejte online nebo si stáhněte Provozní pokyny pro Připojení projektoru Draper SL10. Draper SL10 Operating instructions Uživatelská příručka

Shrnutí obsahu

Další dokumenty pro Připojení projektoru Draper SL10

Komentáře k této Příručce

Související produkty a manuály pro Připojení projektoru Draper SL10